Exercising Pet Safety with Fertilizer Use

Each year hundreds of pets are sent to the vet due to exposure or ingestion of fertilizers. Protect not just your pets but your family as well by learning the risks of using pesticides and fertilizers.  Keeping pests at bay and maintaining a lawn using fertilizers is part of owning a home.  It is important that you follow all the necessary safety precautions to ensure your pet does not get sick when exposed to it.

According to Fertilizer Company Minnetonka MN experts, pesticides and fertilizers are designed to kill weeds, rodents, mosquitoes and a whole lot of other things. While not intended to harm us, if the pesticides are ingested or absorbed into our body via the air or through the mouth, nose, skin and paws it can do a lot of damage.

Danger

The danger to pets especially to dogs is they love to walk around our lawns and gardens as well as other areas that are treated chemically on a regular basis.  This means they unknowingly absorb harmful chemicals or possibly even eat or ingest something that contains them.

Keep your Fertilizer Away from Pets

Make sure that you properly store your pesticides and fertilizers away from the reach of kids and pets. Ensure that the lids are properly sealed and that there is no leakage. Check the manufacturer label on when you could safely allow your pet to roam the garden after you have sprayed it with pesticide or fertilizer.  The best solution is to put them away in a locked area or cabinet.

Fertilizer Company Long Lake MN specialists recommend keeping your pesticides in their original containers as transferring them to your own risk losing the directions for its use as well as increase the chance of having a loose-fitting lid or leak.  Never use the product near pet bowls, toys or sleeping areas to minimize the risk of exposure.

Discuss with your Vet

It is always a good idea to speak with your vet in order to get more information about the effect of pesticides or fertilizers on pets as well as what to do in the event that there is exposure or ingestion.

https://youtube.com/watch?v=-NpVIEtlyBc

Exercising Pet Safety with Fertilizer Use

Each year hundreds of pets are sent to the vet due to exposure or ingestion of fertilizers. Protect not just your pets but your family as well by learning the risks of using pesticides and fertilizers.  Keeping pests at bay and maintaining a lawn using fertilizers is part of owning a home.  It is important that you follow all the necessary safety precautions to ensure your pet does not get sick when exposed to it.

According to Fertilizer Company Minnetonka MN experts, pesticides and fertilizers are designed to kill weeds, rodents, mosquitoes and a whole lot of other things. While not intended to harm us, if the pesticides are ingested or absorbed into our body via the air or through the mouth, nose, skin and paws it can do a lot of damage.

Danger

The danger to pets especially to dogs is they love to walk around our lawns and gardens as well as other areas that are treated chemically on a regular basis.  This means they unknowingly absorb harmful chemicals or possibly even eat or ingest something that contains them.

Keep your Fertilizer Away from Pets

Make sure that you properly store your pesticides and fertilizers away from the reach of kids and pets. Ensure that the lids are properly sealed and that there is no leakage. Check the manufacturer label on when you could safely allow your pet to roam the garden after you have sprayed it with pesticide or fertilizer.  The best solution is to put them away in a locked area or cabinet.

Fertilizer Company Long Lake MN specialists recommend keeping your pesticides in their original containers as transferring them to your own risk losing the directions for its use as well as increase the chance of having a loose-fitting lid or leak.  Never use the product near pet bowls, toys or sleeping areas to minimize the risk of exposure.

Discuss with your Vet

It is always a good idea to speak with your vet in order to get more information about the effect of pesticides or fertilizers on pets as well as what to do in the event that there is exposure or ingestion.

https://youtube.com/watch?v=-NpVIEtlyBc

The Importance of the Location of Your Water Heater

“Location, location, location” – this is the tried and true adage when we are looking to purchase a home or setting up a place of business.  Truth be told, this saying is true for most things like the location of the water heater inside your home. Here are some situations to prove it.

“It’s located in the garage, there is nothing to worry about.”

Most folks dismiss the idea of a potential issue about water heaters since it is located in the garage far away from the reach of kids and pets or nosy houseguests.   True there is a veneer of safety and convenience by putting the heater in the garage but it is not a foolproof you will not encounter problems.  According to Minneapolis water heater plumbers, most water heaters are placed on stands when they are installed in the garage. This is so in order to keep the gas burner at least 18 inches off the floor. To ensure the 18 inch clearance required, builders often extend the higher sub-floor from an adjoining room above the crawlspace, just away enough to establish the platform for the heater and the furnace.

A leaking water heater may quickly damage the floor and the walls in the nearby room. It is not unusual to discover damaged hardwood floors or wall damage within the home caused by a water heater installed in the garage.

“My water heater sits in a pan so I’m OK.”

While pans are quite good at preventing damage from a leaking water heater, not all are equipped with drains and most pans are only designed to prevent a small volume of water from flooding the home.

Preparation is Key

All able persons living in the home should know how to shut off water, gas and electricity in the event of an emergency. It also would be a good idea to know the contact information of the nearest Minneapolis water heater repair professional in case something bad happens with the water heater.

Most water heaters are stored in areas that are inaccessible or somewhere that can easily be ignored by the homeowner thinking it is safe. The key step to preventing problems is to ensure regular maintenance and inspection is done.

4 Signs of an Impending Water Heater Fail

Water heaters are important devices that you use every single day. They provide you with hot water for bathing, cooking and cleaning purposes.  If you have an old water heater make sure you practice preventive maintenance on it to ensure it functions optimally.  Avoid damage and disruption of your hot water supply by knowing the 4 signs of an impending water heater failure

Age

According to Minneapolis water heater plumber experts most water heaters need to be replaced if they are more than ten years old to prevent leaks and disruption. If it is in a location where a leakage will not produce damage to the immediate area then you can just safely wait for it to fail prior to replacing it.

Presence of Rusty Water

Rusty water coming from the heater originating from the hot side piping is a clear sign that the water heater is rusting from within and may be leaking soon. However, if you have galvanized piping it is possible that you may have just rusty pipes to begin with.  In order to avoid replacing a fully functioning water heater by mistake just drain a few five gallons of hot water out.  If by the third bucket, the water coming out is still rusty, chances are the water heater is at fault.

Noise and Rumbling

As the water heater ages, sediment begins to build on the bottom of the tank. The cycle of heating and reheating will cause this sediment to harden eventually. Once this occurs you will begin to hear the rumbling and banging sounds as the water heater is heating up. This is a sure sign that the heater is at the end of its life cycle. Hardened sediment results in less heating efficiency resulting in higher gas or electricity costs for you. Secondly, the extra time needed to heat the water causes more stress on the tank itself leading to tiny leaks.

Presence of Water around the Heater

Call your friendly St. Paul water heater expert expert if you begin to notice moisture around the heater as this is a sure sign of a leak or fracture in the tank.  This occurs because the metal heats causing it to expand and if there are slight fractures the leaks occur. Once it cools the inner tank will contract and the leaks will usually stop.

Essential Tips on Safe Water Heater Care

Your water heater is an important device that provides you with all the heated water for your everyday needs.  It is also a sound investment that you should take care of if you want it to last a long time. Caring for your water heater is easy, here are some essential tips to consider.

Determine Where it is Located

This is a no-brainer as you cannot begin preventive maintenance procedures if you do not know where your water heater is located in the house. The important thing to know is that you need to have good access to it. There are instances where the heater is tucked away in a location that is very hard to reach such as an attic. 

Know What Kind You Have

There are several kinds of water heaters available in the market and the type of preventive maintenance necessary for these varies with each type.  Determine whether you have natural gas, electric or propane or whether its storage tank or tankless type system.  Be sure to take note of the model and serial number or at least know where that information is located in the tank.  This is important for warranty purposes and this is also the information your Minneapolis water plumber expert will inquire about should you need to get it fixed.

Know How to shut it down

In emergency situations like a possible gas leak, it is in your best interest to know how to shut off the water and the fuel or power source for the water heater.  According to Minneapolis water heater repair pros, you should be able to ascertain the presence of a gas valve or a disconnect button within striking distance of the water heater. It is also an excellent idea to have knowledge of the location of the main gas shut-off valve or the part of the breaker that controls the water heater.

Clear the Space around the Water Heater

To prevent inefficiency in heating as well as a potential fire hazard, make sure the area around the heater is clear of anything.

Flush the Water Heater

Do this at least once a year to clear it off any build up in debris and sediments.  Start by draining a few gallons out of the water heater using the drain valve and then get a five-gallon bucket or garden hose to flush it.

Your water heater is an important device that provides you with all the heated water for your everyday needs.  It is also a sound investment that you should take care of if you want it to last a long time. Caring for your water heater is easy, here are some essential tips to consider.

Determine Where it is Located

This is a no-brainer as you cannot begin preventive maintenance procedures if you do not know where your water heater is located in the house. The important thing to know is that you need to have good access to it. There are instances where the heater is tucked away in a location that is very hard to reach such as an attic. 

Know What Kind You Have

There are several kinds of water heaters available in the market and the type of preventive maintenance necessary for these varies with each type.  Determine whether you have natural gas, electric or propane or whether its storage tank or tankless type system.  Be sure to take note of the model and serial number or at least know where that information is located in the tank.  This is important for warranty purposes and this is also the information your Minneapolis water plumber expert will inquire about should you need to get it fixed.

Know How to shut it down

In emergency situations like a possible gas leak, it is in your best interest to know how to shut off the water and the fuel or power source for the water heater.  According to Minneapolis water heater repair pros, you should be able to ascertain the presence of a gas valve or a disconnect button within striking distance of the water heater. It is also an excellent idea to have knowledge of the location of the main gas shut-off valve or the part of the breaker that controls the water heater.

Clear the Space around the Water Heater

To prevent inefficiency in heating as well as a potential fire hazard, make sure the area around the heater is clear of anything.

Flush the Water Heater

Do this at least once a year to clear it off any build up in debris and sediments.  Start by draining a few gallons out of the water heater using the drain valve and then get a five-gallon bucket or garden hose to flush it.

How to Fix Not Enough Hot Water or Too Hot Water on your Water Heater Device

The two most common problems people encounter with water heaters are they produce water that is not hot enough or they are simply too hot. Before you call your friendly water heater plumber expert in Minneapolis, be sure to turn the temperature dial to its desired level, wait a little bit and then recheck.  If the problem persists check out some of the useful tips down below.

Hot Water Not Enough

The usual problem if you do not get enough hot water is an undersized water heater This is especially true if you have noticed the problem for quite awhile already. Have you recently installed a high-flow shower or a new soaking tub that increased your hot water requirements? If so, you will definitely need a bigger water heater. If you do not want to encounter this problem again, checkout tankless water heaters, which can supply you with hot water constantly.

If there is no recent increase in demand for hot water yet you do not get enough of it still, consider also if outdoor temperatures have gone down which will explain why it would be more difficult for your hot water heater to store and maintain water to the temperature you prefer. Adjust the thermostat accordingly.  Do check for leaks in and around the hot water heater, if there is none try flushing the water heater tank in order to remove any mineral deposits that are quite notorious for reducing the heater’s efficiency.

Check also the temperature-pressure relief valve, this device keeps the pressure from going up too much in the boiler itself. Simply lift or lower its handle, the water should be able to drain easily from the overflow pipe. If it does not, call your friendly neighborhood Minneapolis water heater repair expert.

Hot Water Too Hot

The first step is to adjust the thermostat. Nine times of ten that fixes the problem. Make sure to note the current setting by marking it with a felt-tip pen and then start turning the knob to the cooler setting. If you notice excessive steam or boiling sounds within the water heater itself chances are it is not shutting off at the set temperature.  In this case, the temperature-pressure relief valve may be the problem, turn the water heater’s temperature to cool the water off and then replace the heater’s pressure valve.

Water Heater Troubleshooting Advice

When it comes to gas water heaters there are three usual problems that are normally seen. The first one is that the water heater does not heat water at all.  The second is it heats it up but it does not do so in the desired amount and lastly the pilot light does not stay lit. Here are some recommendations from your friendly Minneapolis plumber water heater experts.

No Heat

The first thing that you need to check is to ensure that the gas to the water heater is turned on. To do so, you need to put into PILOT the gas control knob so as to prevent the burner from igniting when you are peering inside. Carefully remove the metal cover located at the bottom and check to see if the burner as well as the pilot light, which is the small flame, located at the end of the pilot gas tube is also lit up.

No Pilot Light

Refer to the instructions on the tank on how to relight it. Check also the gas inlet valve to determine if it has been closed fully or just partially. If it is, just turn the handle parallel to the line and then relight the pilot. If it still does not light up, it is possible that the thermocouple could be at fault. If you live in Minneapolis there are water heater repair experts you can call to repair the problem right away.

Burner not on

To correct the problem, replace the cover and ensure that the thermostat is set to at least 120 degrees Fahrenheit.  If done, turn the hot water faucet on and wait for a few minutes to determine if the water heater burner begins to ignite. If it does not, just leave it running and attempt to lower and raise the temperature setting until it does.

When Burner Ignites

Put the cover back and then turn the thermostat to its correct level. At this point if the burner does not ignite, have it checked by a certified technician.

Check for Gas

If you notice a garlic-like scent, please turn the gas valve control to OFF and then wait until such time that the smell has disappeared prior to relighting the pilot light. If the smell is too strong and does not go away, turn the gas control valve off immediately, open the windows to ventilate and call the utility company.

When it comes to gas water heaters there are three usual problems that are normally seen. The first one is that the water heater does not heat water at all.  The second is it heats it up but it does not do so in the desired amount and lastly the pilot light does not stay lit. Here are some recommendations from your friendly Minneapolis plumber water heater experts.

No Heat

The first thing that you need to check is to ensure that the gas to the water heater is turned on. To do so, you need to put into PILOT the gas control knob so as to prevent the burner from igniting when you are peering inside. Carefully remove the metal cover located at the bottom and check to see if the burner as well as the pilot light, which is the small flame, located at the end of the pilot gas tube is also lit up.

No Pilot Light

Refer to the instructions on the tank on how to relight it. Check also the gas inlet valve to determine if it has been closed fully or just partially. If it is, just turn the handle parallel to the line and then relight the pilot. If it still does not light up, it is possible that the thermocouple could be at fault. If you live in Minneapolis there are water heater repair experts you can call to repair the problem right away.

Burner not on

To correct the problem, replace the cover and ensure that the thermostat is set to at least 120 degrees Fahrenheit.  If done, turn the hot water faucet on and wait for a few minutes to determine if the water heater burner begins to ignite. If it does not, just leave it running and attempt to lower and raise the temperature setting until it does.

When Burner Ignites

Put the cover back and then turn the thermostat to its correct level. At this point if the burner does not ignite, have it checked by a certified technician.

Check for Gas

If you notice a garlic-like scent, please turn the gas valve control to OFF and then wait until such time that the smell has disappeared prior to relighting the pilot light. If the smell is too strong and does not go away, turn the gas control valve off immediately, open the windows to ventilate and call the utility company.

Guide to Safe Farming

You might think what could happen on a farm? Well lots of things if you are not careful. For instance, you can get crushed by the very tractor you’re driving or get wrapped around a PTO shaft.  You could get rammed by an angry sow if you seem too cocky and agitate her. If you are new to farming or planning to invest in one do not let safety hazards stop you from achieving your dream. Here are some farm safety tips to live by.

Personal Farm Safety

Agricultural equipment MN experts recommend not wearing any loose clothing around work areas.  Always use safety equipment the way it was designed. This means using the correct gloves, hearing protection and safety eyewear equipment. If working in a dusty farm environment then respirators and face masks are a must.  If you have children in the farm, do discuss safety concerns with them and be sure you practice what you teach or else they will not follow you if they see you regularly violating safety rules.

Tractors and Implements

Farm equipment MN safety specialists recommend keeping tractor roll-over protection structures in their proper place. If your tractor does not have one yet, be sure to have one installed immediately. Do not let anyone ride on tractor fenders, hitches or any implements and attachments. Do shield all PTO-powered equipment drive shafts and keep kids at a distance away from them. Do not start gas or diesel engines in an enclosed area without any good ventilation in order to avoid carbon monoxide poisoning

Make sure your tractor and farm trucks have first aid kits and fire extinguishers. Regularly perform maintenance checks on these as they have an expiration date.  Do not get off the tractor without ensuring that it is in park or pulling the emergency brakes and do not ever leave any running power equipment unattended.

Livestock

Make sure all your farm animals are in good health and separate those that are possibly ill. Treat all farm animals with the respect they deserve. If you know how they behave you are ready for their actions. Do take extra precautions during birthing or breeding, as they are naturally quite aggressive at this time.

You might think what could happen on a farm? Well lots of things if you are not careful. For instance, you can get crushed by the very tractor you’re driving or get wrapped around a PTO shaft.  You could get rammed by an angry sow if you seem too cocky and agitate her. If you are new to farming or planning to invest in one do not let safety hazards stop you from achieving your dream. Here are some farm safety tips to live by.

Personal Farm Safety

Agricultural equipment MN experts recommend not wearing any loose clothing around work areas.  Always use safety equipment the way it was designed. This means using the correct gloves, hearing protection and safety eyewear equipment. If working in a dusty farm environment then respirators and face masks are a must.  If you have children in the farm, do discuss safety concerns with them and be sure you practice what you teach or else they will not follow you if they see you regularly violating safety rules.

Tractors and Implements

Farm equipment MN safety specialists recommend keeping tractor roll-over protection structures in their proper place. If your tractor does not have one yet, be sure to have one installed immediately. Do not let anyone ride on tractor fenders, hitches or any implements and attachments. Do shield all PTO-powered equipment drive shafts and keep kids at a distance away from them. Do not start gas or diesel engines in an enclosed area without any good ventilation in order to avoid carbon monoxide poisoning.

Make sure your tractor and farm trucks have first aid kits and fire extinguishers. Regularly perform maintenance checks on these as they have an expiration date.  Do not get off the tractor without ensuring that it is in park or pulling the emergency brakes and do not ever leave any running power equipment unattended.

Livestock

Make sure all your farm animals are in good health and separate those that are possibly ill. Treat all farm animals with the respect they deserve. If you know how they behave you are ready for their actions. Do take extra precautions during birthing or breeding, as they are naturally quite aggressive at this time.

How to achieve a Winter-Ready Snow Blower

Most homeowners weary of a long winter season put away the snow blower and forget about it once spring arrives. However, when the cold season comes by again, the snow blower needs to be ready to work before the first snowfall hits the ground.  Homeowners are faced with a couple of options namely pray the blower starts the moment you need it or perform routine maintenance on the machine prior to the onset of another winter season.

Safety First

According snow blowers MN specialists, prior to any maintenance steps one needs to ensure that the engine is completely turned off which include removing the spark plug and the wire. Normally, the wire and boot are in plain sight either on the top or at the back. Simply pull the boot off as well as the spark plug to prevent any chances for the engine to start by chance.

Change Snow Blower Oil

The location of the oil drainpipe is usually on the side or back of the machine. Simply unscrew the end and tip of the machine to allow the oil to drain out into a can or a drain pan. Next step is to add new oil like 5W-30 (please do check the owner’s manual for recommendations) by inserting a funnel into the hole where the dipstick goes and then pouring the fresh oil in. Make sure to pause occasionally while adding new oil to check if the recommended amount has been put in. Avoid overfilling the engine as it can cause severe damage.

Drain Old Gas

Equipment parts and service MN experts recommend draining out old gas that has been sitting in the tank for months, as this is no longer good to use on the snow blower. There are some machines that feature a drain valve on the bottom of the tank. If your machine does not have this, removing the rubber gas line on the bottom will allow the gas to eventually drain out.

Make sure to replace the spark plugs and replace it with new ones based on manufacturer recommendations. If your machine features a belt, do check for signs of cracking or fraying and then replace accordingly.

Fixing a Jammed Snow Blower

One of the most annoying things to encounter in the dead of winter is a jammed snow blower. Usually a jammed snow blower is quite easy to fix once you are able to locate and remove whatever is jamming it but you also need to ensure you are working safely.  Before you attempt fixing a jammed snow blower make sure you turn it off completely first and wear gloves to avoid risk of serious injury. Here are some helpful tips on how to fix a jammed snow blower

Blocked Output Chute

According to snow blowers MN experts, one of the most common causes of snow blower malfunction is a blocked output chute.  In this scenario, the blower continuous to run but no snow is ejected from the output shaft.  To address this, turn the snow blower off and disconnect the spark plug. Get a shovel and use the handle to rake or break any collected ice and packed snow that is jamming the chute.  Output chutes tend to jam up if you push the snow blower too quickly or if the snow is quite slushy. 

In order to prevent this scenario, slow down the snow blower, as it is only capable of taking in as much snow as the impeller can move. It is not recommended using the chute on a wet or slushy snow, as it will almost certainly result in a jam.

Ice-Blocked Auger

According to equipment part and service MN specialists, a snow blower’s auger will jam up if it is trying to blow snow that is too wet and too fast movement resulting in an inability of the blades to keep up. To correct this, turn the blower off and remove the spark plug to ensure the engine will not start accidentally.  Use a shovel to remove any ice and snow around the auger blades. Once all the snow and ice is removed around it you can now reconnect the spark plug.

Objects

It is not unusual for foreign objects to get stuck inside a snow blower. Most common ones are children’s toys and newspaper. If it is the latter, use warm soapy water to soften it first and then use a long handled tool like a rake handle to remove it. Try prying out the toy with a shovel or rake handle. Be sure the engine is completely off prior to attempting any foreign object.